Replace Ram to LIMA pro M1451G
With photos illustrate the various steps made to change the ram to LIMA M1451G, as the sticks of ram are located behind the motherboard ..
Do not tee off at this if you do not have at least a minimum of knowledge about it ..
List of issues (you still have time not to do so)
1The ram is behind the motherboard ..
2 is necessary to bend the plate a little bit of the laptop (nell'inserimeto to work better then we will see the pin, and nn I assure you that you will insert)
3 Re-plug the keyboard that we have to remove by force ..
4 Then there are problems, but only a simple takedown and frame ..
We begin ...
Remove the bottom dell'amilo, being careful to remove the CD player and unscrew the bolts under it .. 
Begin to pull the fan with the cooling system.
Then switch to disconnect all the plugs that you see the mother sheda ..
So we have an opening up of the motherboard so .. 
to remove the motherboard you're forced to unplug the keyboard from here (although we complicate this very life)
So we would be in the hands of the motherboard 
Change the ram ..
Now we begin to climb
The problem that I mentioned at the beginning here is to insert the plug (the sign with screwdriver)
First you should bend 3 parts of tin as a sign, to be able to move better sheda mother ..
There may be 2 ways 2 sticks or cut the ears and make a mark where we cut, so 
then try to insert the pin through these 2 holes 
so 
Or, replace the sticks with a small screwdriver Italian ..
I was there I tinkered a couple of minutes but the result was there (if not, I was not driving)
For questions or clarifications you say as well.
7 Comments »
You can leave a response , or make a trackback from your own site.
Published on 26 05th, 2009 at 21:13 | Number: 1
just unscrew the screw K / B under the pc and turn up the computer keyboard. The sticks of ram are below essa.ciao
Published on 26 05th, 2009 at 21:57 | Number: 2
I'll try it right now because the reader does not work, I tried to remove the cmq tastira but the result was bad, was bloccatta, I do not know, it seemed that between the houses and the keyboard there was a glue or double-sided tape (which is strange, but I removed a piece) ... A few days of this we try again ..
Thank you anyway
Posted on 01 11th, 2010 at 23:16 | Number: 3
just unscrew the screw K / B under the pc and turn up the keyboard.
If you have found it difficult to extract the keyboard is probably because there is only need to unscrew the screw k / b on the bonds of the PC, but then you must act with a screwdriver baby cut some of which are metal strips along the edges of the keyboard, in a few words in the cavity above the keys f1, f2, f3 etc. ... I hope to check out was of help ...
Your transaction has been effective but high, very high risk .... Besides the fact that it also creates probemi in replacement ..
the next
John
ps I seek information on this laptop, especially if someone has tried to replace the video card ATI Mobility Radeon x300 with x700 or higher ....
think that there may be conflicts?
Published on 15 05th, 2010 at 18:27 | Number: 4
Hello, I wanted to ask how much ram you sucsa added or you just replaced? If you support this much RAM Maximum PC? I saw that there are two slots I can put 2 x 1 gig?
Published on 16 05th, 2010 at 03:38 | Number: 5
Do not remember how many MB supported .. I do I put a bank of 2gb ram.
CMQ is written in the manual
Published on 19 05th, 2010 at 01:35 | Number: 6
I feel much of a problem, I burned the integrated ram which is just above the left, is seen moving a little 'sticker is black, as is unreadable let me know what kind of integrated ...
Published on 19 05th, 2010 at 15:51 | Number: 7
Welcome,
although I think it will be difficult.
I gave the notebook to listen.
So I could not tell what kind of component.
If I happen to support a notebook of this type let you know
You can try (excluding the calculation to adjust an integrated) to see if you can read these letters and do some comparison.